Toyota Supra JZA80 Soarer Front Drift Angle Lock Kit

$2,600.00
excluding VAT
In stock
SKU
WF080
or View Spares

 

Legendary Toyota Supra with double wishbone suspension enables 65 degrees of usable lock with adjustable Ackermann settings on Wisefab Supra suspension kit. While providing over 60 degrees of lock, this kit is engineered and tested to optimize a lot of other parameters that make a difference in handling and performance. Very easy to install and adjust. Wisefab has engineered an adjustable shock absorber motion ration on the lower control arm. Set your desired toe in and enjoy. Adjust the stiffness while not changing the ride height. All the parts in the lock kit are provided as spare parts.

Want to know how does Wisefab Lock kit fits your driftcar check below the link CHECK FITMENT or here!

Check out the Toyota Supra suspension kit for the rear.

Scroll down to order your spare parts conviently right here!

Here is our recommended alignment parameters:
Toe in/out: If Ackermann is 0 or negative then toe is 2mm out. If Ackermann is positive then toe is 0
Camber: -3,3 +/-0,3
Caster: 3 +/-0,3

  • 65 degrees of lock, parallel steering.
    Both wheels turn the same angle. You could tune your steering geometry either towards positive or negative Ackermann in just a few minutes even at trackside without messing up an alignment. 
    Ackermann adjustment kit included.
  • Higher roll center (RC). 
    On Wisefab knuckle, both joints have lowered about 60mm, which brings the front RC up on lowered car, providing higher roll stiffness and letting to remove the front anti roll bar (sway bar) that is quite difficult to package with that high lock angles.
  • Very good camber control and minimal bump steer with high steering angles. 
    On drift cars the dynamic camber and bump steer is much more important than static. With our kinematics we have assured that the camber would provide very good front grip and bump steer is minimal at all the range of steering.
  • Steering jacking control.
    During drifting, when steering angle is much bigger, jacking is also bigger, even with the same geometry and it could become a problem. We have changed the geometry that it doesn’t cause any handling issues.
  • Consistent and predictable self-alignment torque. 
    Caster is not the only important parameter to provide sufficient self-alignment torque especially at high lock. It’s the combination of different parameters to maintain consistent trail and self-alignment torque. With our setup the steering wheel turns always to the direction of movement and doesn’t get stuck at full lock.
  • Adjustable spring and shock absorber motion ratio. 
    The shock lower bracket has 3 attachment possibilities, which allows to change suspension stiffness and handling very quickly without changing the spring and messing up ride heights.
More Information
Make Toyota
Field Drift
Placement Front
Prodmaster Name Drift Angle Lock Kit
Wisefab fitment calculator
Make and Model
?
Fender Arch Height from Ground (mm)
Tire Width
Tire Height or Diameter
Rim Diameter
Rim Width
ET
Wheelspacer (mm)
Suspension selection
Suspension selection
OEM
WISEFAB
CUSTOM
 
1785 mm
1785 mm
Fender to Fender
1620 mm
1782 mm
Hub to Hub
0 °
-4 °
Camber
3 °
3 °
Caster
0 mm
-2 mm
Toe

Set your desired rim and tire parameters in our fitment calculator to have a better overview how Wisefab will transform your driftcar. Fender arch height is your indicator on ride height. Check the fitment and learn about missing fender gap before ordering widebody kit. In the custom section you can edit the fender to fender and wheelhub to wheelhub measurments according to your driftcar. Use the max width to check if your car will fit on your trailer. Have fun with this fitment calculator.

Spare parts

All
Complete parts
Left Knuckle
Right Knuckle
Upper Control Arm
Tie Rod Assembly
Left Lower Control Arm
Right Lower Control Arm

Complete parts

Complete parts

1
Knuckle
Left
WF080_100LA
$560.00
excluding VAT
Right
WF080_100RA
$560.00
excluding VAT
3
Upper Control Arm
WF080_300A
$355.00
excluding VAT
4
Tie Rod Assembly
WF080_600A
$105.00
excluding VAT
5
Lower Control Arm
Left
WF080_200LA
$500.00
excluding VAT
6
Lower Control Arm
Right
WF080_200RA
$500.00
excluding VAT

Left Knuckle

Left Knuckle

2
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$4.30
excluding VAT
3
BushingT ID 8 OD22 h46
WF080_922
$16.00
excluding VAT
4
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$2.30
excluding VAT
5
Bolt Hex M14x1.5x 80 RH 10.9 ST DIN 960
B01114150080R3SD960
$13.00
excluding VAT
6
Washer FlatSmall M14 ZN DIN433
B03214NAZD433
$2.30
excluding VAT
7
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
B02214150R2ZD9858
$2.30
excluding VAT
8
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$4.30
excluding VAT
9
BushingT ID 8 OD16 h46
WF080_923
$13.00
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
11
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$2.30
excluding VAT
12
Ackermann Washer Round 0 offset
WF013_140
$11.00
excluding VAT
13
Ackermann Washer Round 3 Offset
WF080_142
$11.00
excluding VAT
14
Ackermann Washer Round 4.5 Offset
WF080_143
$11.00
excluding VAT
15
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
B01110150060R3SD931
$4.30
excluding VAT

Right Knuckle

Right Knuckle

2
Bolt AllenButton M 8x1.25x 60 RH 8.8 ZN ISO7380
B01408125060R2ZI7380
$4.30
excluding VAT
3
BushingT ID 8 OD22 h46
WF080_922
$16.00
excluding VAT
4
Nut Nylock M 8x1.25 RH 8.8 ZN DIN985-8
B02208125R2ZD9858
$2.30
excluding VAT
5
Bolt Hex M14x1.5x 80 RH 10.9 ST DIN 960
B01114150080R3SD960
$13.00
excluding VAT
6
Washer FlatSmall M14 ZN DIN433
B03214NAZD433
$2.30
excluding VAT
7
Nut Nylock M14x1.5 RH 8.8 ZN DIN985-8
B02214150R2ZD9858
$2.30
excluding VAT
8
Bolt Hex M10x1.5x 65 RH 10.9 ST DIN 931
B01110150065R3SD931
$4.30
excluding VAT
9
BushingT ID 8 OD16 h46
WF080_923
$13.00
excluding VAT
10
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
11
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$2.30
excluding VAT
12
Ackermann Washer Round 0 offset
WF013_140
$11.00
excluding VAT
13
Ackermann Washer Round 3 Offset
WF080_142
$11.00
excluding VAT
14
Ackermann Washer Round 4.5 Offset
WF080_143
$11.00
excluding VAT
15
Bolt Hex M10x1.5x 60 RH 10.9 ST DIN 931
B01110150060R3SD931
$4.30
excluding VAT

Upper Control Arm

Upper Control Arm

2
Nut Special M14x1.50 RH ZN SPC
WF080_908
$20.00
excluding VAT
3
Rod end 16x1.5 RH male CrMo
SRODEND16X1.5 RH M
$39.00
excluding VAT
4
Spacer ID14 OD16 h 4.5
WF080_909
$11.00
excluding VAT
5
Nut Thin M16x1.5 RH 8.8 ZN DIN936/439
B02316150R2ZD936/439
$4.30
excluding VAT
6
Bolt Allen M14x1.50x200 RH 12.9 ST SPC
WF080_907
$48.00
excluding VAT
7
Spacer ID10 OD12 h14
WF080_906
$13.00
excluding VAT
8
C-Clip InternalSTD d26 ST DIN472
B04126SD472
$2.30
excluding VAT
9
Spherical ID12/OD26
SSPHERICAL 12/26
$35.00
excluding VAT

Tie Rod Assembly

Tie Rod Assembly

2
Tie Rod Inner M14x1.5 M14x1.5 L366
STIEROD_M14_M14_L366
$31.00
excluding VAT
3
Spacer ID10 OD14 h 5.4
WF080_921
$11.00
excluding VAT
4
Rod end 14x1.5 RH female CrMo
SRODEND14X1.5 RH F
$39.00
excluding VAT

Left Lower Control Arm

Left Lower Control Arm

2
Spacer ID16 OD18 h23.7
WF080_901
$13.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$48.00
excluding VAT
4
Nut Thin M18x1.5 RH 8.8 ZN DIN936/439
B02318150R2ZD936/439
$4.30
excluding VAT
5
Spacer ID16 OD18 h22.25
WF080_902
$13.00
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
7
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$2.30
excluding VAT
8
Lower Control Arm Shock Mount
WF080_220
$30.00
excluding VAT
9
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$4.30
excluding VAT
10
Spacer ID14 OD18 h 8.5
WF080_903
$13.00
excluding VAT
11
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$2.30
excluding VAT
12
Spherical ID18/OD35
SSPHERICAL 18/35
$39.00
excluding VAT

Right Lower Control Arm

Right Lower Control Arm

2
Spacer ID16 OD18 h23.7
WF080_901
$13.00
excluding VAT
3
Rod end 18x1.5 RH male CrMo
SRODEND18X1.5 RH M
$48.00
excluding VAT
4
Nut Thin M18x1.5 RH 8.8 ZN DIN936/439
B02318150R2ZD936/439
$4.30
excluding VAT
5
Spacer ID16 OD18 h22.25
WF080_902
$13.00
excluding VAT
6
Nut Nylock M10x1.5 RH 8.8 ZN DIN985-8
B02210150R2ZD9858
$2.30
excluding VAT
7
Washer FlatSmall M10 ZN DIN433
B03210NAZD433
$2.30
excluding VAT
8
Lower Control Arm Shock Mount
WF080_220
$30.00
excluding VAT
9
Bolt Hex M10x1.5x 35 RH 10.9 ST DIN 933
B01110150035R3SD933
$4.30
excluding VAT
10
Spacer ID14 OD18 h 8.5
WF080_903
$13.00
excluding VAT
11
C-Clip InternalSTD d35 ST DIN472
B04135SD472
$2.30
excluding VAT
12
Spherical ID18/OD35
SSPHERICAL 18/35
$39.00
excluding VAT
Wisefab Nissan 240sx
"’We started working together with Wisefab back in 2014 when we launched our Falken Tyres Nissan 240sx for European competition. Since then, we have enjoyed working closely with the engineers at Wisefab testing new products before going into production and have had a lot of success winning multiple championship worldwide. Thank you to everyone at Wisefab for believing in us and producing such top-quality products."
Nissan 240sx Drift
“When I first installed a Wisefab lock kit it truly opened the door for some more aggressive driving style. I quickly began to expect nothing less than the massive angle and performance that Wisefab provides and installed a lock kit on all (4) of my Nissan 240sx that I currently drift. Also, after testing what I though was a very competitive rear suspension solution against the latest Wisefab rear kit, I was blown away with the apparent grip gain the rear Wisefab kit yielded. I am so thankful that Wisefab has poured so much effort into creating a bolt on suspension solution that transforms a Nissan 240sx into what I believe is still the most competitive drift chassis in the world."
Nissan 240sx Lock kit
"I love the Wisefab suspension kits used on my competition and demo vehicles, they provide all the angle and grip we love along with the strength and durability we need to compete with the best!"
Toyota 86 Drift
"I wouldn't have half the results! Only by running Wisefab in my Toyota 86 it just makes the car handle so good and let's me adjust set up pretty easy which is a massive help going from track to track!"